OPAQUE

TOOLS

Tools

  • degreaser
  • felt squeegee
  • utility knife
We recommend applying the sticker with 2 people.


These instructions apply to:

! Note that there is an overlap of 8 mm if your wall sticker consists of different parts. Apply the second strip 8 mm over the previously applied strip to ensure the pattern matches up.

APPLICATION

Quality check:
Unroll your sticker on a clean and dry surface with the printed side facing up to ensure it is in good condition. Check for printing or manufacturing defects, such as discolourations, deformations or alignments errors.


Prepare the surface:
The surface must be dry, smooth and free from dust. Any imperfections will be visible underneath so make sure to repair them before applying the sticker. Remove door handles, key plates and handles, and clean the surface with a degreaser.

Step 1

1. Carefully peel off the release paper.

Step 2

2. Apply the sticker and smooth out the surface with a felt squeegee while a second person pulls it tight.

Step 3

3. Push out any air bubbles through the built-in micro channels.

Step 4

4. Cut off any excess and cut-outs with a sharp utility knife.

FINAL EFFECT

TRANSPARENT

TOOLS

Tools

  • degreaser
  • felt squeegee
  • utility knife
  • water sprayer
We recommend applying the sticker with 2 people.


These instructions apply to:

APPLICATION

Quality check:
Unroll your sticker on a clean and dry surface with the printed side facing up to ensure it is in good condition. Check for printing or manufacturing defects, such as discolourations, deformations or alignments errors.


Prepare the surface:
The surface must be dry, smooth and free from dust. Any imperfections will be visible underneath so make sure to repair them before applying the sticker. Remove door handles, key plates and handles, and clean the window with a degreaser.

Step 1

1. Peel off the paper for about 30 cm and spray both the window and the adhesive side of your sticker with water.

Step 2

2. Apply your sticker on the glass while a second person smooths out the surface with a felt squeegee by gently pushing out any air bubbles to the edge.

Step 3

3. After this, peel off the protective film a little more and carefully pull the sticker tight while repeating the above method.

Step 4

4. Air bubbles can be easily removed. Simply prick them with a thin needle and smooth out the surface with a felt squeegee. Cut off any excess and cut-outs with a sharp utility knife.

FINAL EFFECT

Final effect window stickers

SHOP WINDOW STICKERS

*** Please note that our prints are only partly resistant to mechanical wear and tear. Nikkel Art guarantees product quality, but doesn’t control the circumstances and way its products are used. Nikkel Art cannot be held accountable for the work of the designer and executor.

OPAQUE

TOOLS

Tools

  • degreaser
  • felt squeegee
  • utility knife
We recommend applying the sticker with 2 people.


These instructions apply to:

! Note that there is an overlap of 8 mm if your wall sticker consists of different parts. Apply the second strip 8 mm over the previously applied strip to ensure the pattern matches up.

APPLICATION

Quality check:
Unroll your sticker on a clean and dry surface with the printed side facing up to ensure it is in good condition. Check for printing or manufacturing defects, such as discolourations, deformations or alignments errors.


Prepare the surface:
The surface must be dry, smooth and free from dust. Any imperfections will be visible underneath so make sure to repair them before applying the sticker. Remove door handles, key plates and handles, and clean the surface with a degreaser.

Step 1

1. Carefully peel off the release paper.

Step 2

2. Apply the sticker and smooth out the surface with a felt squeegee while a second person pulls it tight.

Step 3

3. Push out any air bubbles through the built-in micro channels.

Step 4

4. Cut off any excess and cut-outs with a sharp utility knife.

FINAL EFFECT

TRANSPARANT

TOOLS

Tools

  • degreaser
  • felt squeegee
  • utility knife
  • water sprayer
We recommend applying the sticker with 2 people.


These instructions apply to:

APPLICATION

Quality check:
Unroll your sticker on a clean and dry surface with the printed side facing up to ensure it is in good condition. Check for printing or manufacturing defects, such as discolourations, deformations or alignments errors.


Prepare the surface:
The surface must be dry, smooth and free from dust. Any imperfections will be visible underneath so make sure to repair them before applying the sticker. Remove door handles, key plates and handles, and clean the window with a degreaser.

Step 1

1. Peel off the paper for about 30 cm and spray both the window and the adhesive side of your sticker with water.

Step 2

2. Apply your sticker on the glass while a second person smooths out the surface with a felt squeegee by gently pushing out any air bubbles to the edge.

Step 3

3. After this, peel off the protective film a little more and carefully pull the sticker tight while repeating the above method.

Step 4

4. Air bubbles can be easily removed. Simply prick them with a thin needle and smooth out the surface with a felt squeegee. Cut off any excess and cut-outs with a sharp utility knife.

FINAL EFFECT

Final effect window stickers

SHOP WINDOW STICKERS